Special Deals on Bostitch Nailers        

Special Deals on Bostitch Nailers tools and information

Find Special Deals on Bostitch Nailers at best prices and buy!

Bostitch N86S-1 Factory Reconditioned Angle Nailer

-The Stanley-Bostitch N86S-1 Factory Reconditioned Nailer is a precision-built tool. Designed for high speed, volume nailing. These stick nailers will deliever efficient, dependable service when used correctly and with care.

Bostitch BA-W9 3/8InchHx1InchW Corrugated/Mitre Fastener

Bostitch BA-W9 3/8Hx1W Corrugated/Mitre Fastener

Bostitch BA-S114P90 9/16Inch Length 18-Gauge Headless Pin Nail

Bostitch 9/16 Length 18-Gauge Headless Pin Nail

Paslode 404717 Rechargeable 6-Volt Battery for Impulse Cordless Nailers

The Paslode 404717 is a replacement battery for the Paslode Impulse Cordless Nailers. It works on Paslode models 900400, 900420, 900600, and 902000. With the 404717 Impulse Battery you have the power to drive up to 4,000 nails in a single charge. Keep a few on hand to minimize downtime and increase productivity. Attention International Customers Paslode products cannot be shipped outside of the USA.

Bostitch F21PL Factory Reconditioned 2Inch - 3-1/2Inch Industrial Stick Framing Nailer, 80 - 120 PSI, 21°

Bostitch F21PL Factory Reconditioned 2Inch - 3-1/2Inch Industrial Stick Framing Nailer, 80 - 120 PSI, 21°

Bostitch CPACK3 Factory Reconditioned Nailer, Stapler, and Compressor Combo Kit

The Bostitch CPACK3 is a factory reconditioned 3-Tool Finish & Trim Combo Kit that includes pneumatic tools such as a finish nailer, a brad nailer, a finish stapler, and an air compressor. The kit also includes an air hose, and canvas tool bag.The compressor in the Bostitch CPACK3 has heavy-duty motor with 2HP power at the peak, and otherwise smoothly works at 1.5 HP, delivering 3.4 CFM @ 40 PSI and 2.1 CFM @ 90 PSI and maximum 135 PSI. It has a tank capacity of 6 gallons and oil-free pump that requires no maintenance.The 16-gauge straight finish nailer can drive 1 ? 2-1/2 nails into toughest material. Moreover, it has a fast release nose to reduce downtime in case of jams. The 18-gauge brad nailer is designed to drive brads varying from 5/8 to 1-1/4. The narrow crown stapler is an 18-gauge tool that can drive 7/32 crown SX staples from ½ to 1. All three tools feature tool-free adjustable exhaust to direct the air away from the user. The non-mar tip protects the surface of the material. The adjustable depth guide enables the user to easily set the nail depth as required by the application. The housing of the tool in the Bostitch CPACK3 is made from aluminum, which is a lightweight and durable material.

Bostitch RN46-1 Factory Reconditioned 1/4Inch Coil Roofing Nailer, 70-120 PSI

The Bostitch RN46-1, a factory reconditioned coil roofing nailer, is a durable power nailer that features a damage resistant body. Its aggressive wear guards and skid pads protects this heavy-duty nailer from any job site damages. Its zero lockout features ensure that the tool gets locked once the last nail is gunned, thus preventing dry run. This aids in understanding when the magazine needs to be reloaded. The carbide inserted nosepiece adds to the durability of this nailer making it last longer than its competitors. The quick-set adjustable depth guide, lets the user set the depth of a nail, when shot, as per the requirement. To address productive time utilization for professionals, the Bostitch RN46-1 features a unique single-action side load canister. This reduces the loading time of the magazine; With a 410in-lbs torque power this tool allows effortless gunning of nails on most of the surface. Moreover, the adjustable shingle guide incorporated in the Bostitch RN46-1, enables a user to quickly space the shingles at the required distance. This coil roofing nailer is an ideal tool for composition roofing, vapor barrier installation, insulation board, vinyl siding, and fiber cement siding.

Bostitch PN100K Impact Nailer Kit

Ideal for driving common bulk nails in confined areas and for nailing of metal connectors and joist hangersMagnetic nose with recessed nail slot holds nails stable for accurate fastener placementHardened steel nose for extreme durability

Bostitch MFN200 Factory Reconditioned 2-Inch Cleat Manual Flooring Cleat Nailer

Ready to use straight out of the box, Bostitch MFN200 Factory Reconditioned 2 Cleat Manual Flooring Cleat Nailer, comes along with a rubber mallet. Simply unpack, load, and strike to nail down and construct stable flooring. Ideal for DIY as well as professional installer this power cleat nailer drives 1 ½ to 2 inches nail with minimal effort. Gun it on hardwood or engineered floors and set the tongue-and-groove joint right for once and for all. The long reach handle of this cleat nailer enhances the comfort of use besides adding to the control. You need not bend every time to strike this nailer. The sturdy aluminum construction makes Bostitch MFN200 endure jobsite abuse. Use it for yourself or let your friends borrow; rest assured this tool will be with you for years. Being a non-pneumatic tool it assures a jam-free operation and lets you smoothly nail an L shaped serrated nail at every strike. More over the rubber bumper prevents the flooring from any sort of damage leaving it neat and spotless. With a magazine capacity of 200 cleats you are freed from the effort of frequent reloading. The 9.5 lbs Cleat Nailer is lightweight, can be easily ported at jobsite and stably drives a nail through inch hardwood flooring.

Bostitch BT200K-2 Factory Reconditioned 5/8Inch to 2Inch Oil-Free Brad Nailer Kit, 18 Gauge

The Bostitch BT200K-2 is a Factory Reconditioned 18 Gauge 5/8 to 2 Oil-Free Brad Nailer Kit. This lightweight tool has magnesium housing for jobsite durability. The oil-free operation prevents stains on work piece. It has ultra-quiet rear exhaust and open nose design for easy jam clearing.

Bostitch MCN150 1-1/2Inch STRAPSHOT Metal Connector Nailer, 80 - 120 PSI, 29 Nails

The Bostitch MCN150 is a 1-1/2 STRAPSHOT Metal Connector Nailer. It has an exposed nail tip which places fastener point directly into connector holes for a faster, more precise application. The compact design fits easily into hard to reach spaces. In-line magazine offers improved balance for added maneuverability.

Bostitch PRO-38REPAIR 3/8Inch Prozhoze Repair Kit

-Compression hose mending kit for 3/8" Prozhoze.

Bostitch RHS8D113HDG Galvanized Diamond Point Nail

-Stick Framing Nails 21 Degree-Plastic Collated Smooth Shank-Hot Dipped- Round Head Boxed-Lgth X Dia. Inches=2-3/8 X .113-Box of 5000

Bostitch BA-S125P50 1Inch 18 Gauge Headless Pins

BA-S125P50 18 Gauge headless pins fit BA-T520 Decorative Molding/Fine Trim Pinner

Bostitch N62FNK-2 Factory Reconditioned 15 Gauge Industrial Oil-Free Angled Finish Nailer Kit, 120 PSI

The Bostitch N62FNK-2 is a Factory Reconditioned Industrial 15 Gauge Oil-Free Angled Finish Nailer Kit. The nailer has an oil-free engine which requires no lubrication. Hence it leaves no oil stains on work. It has a tool-free removable magazine for fast cleaning and jam clearing. It also has an adjustable depth control for quick countersinking adjustments and angled magazine for maximum maneuverability.

Bostitch MIIIFS Factory Reconditioned 1-1/2 Inch to 2 Inch Flooring Stapler Kit, 70-90 PSI

The Bostitch MIIIFS is a Factory Reconditioned 1-1/2" to 2" Flooring Stapler Kit. The compact, mallet-actuated air stapler automatically positions and drives staples for rapid installation of hardwood flooring. It secures the flooring at the proper angle and penetration without the danger of hammer marring. By simply resting the nose of the machine squarely against the work, the direction and angle of the staple is automatically aligned. The stapler is easily adjusted to handle different flooring thickness or tongue positions. It has an aluminum body for job site durability.

Bostitch SX150K-1 Factory Reconditioned 18 Gauge Narrow Crown Stapler

-Lightweight magnesium housing for jobsite durability-Oil-free operation prevents stains on workpiece-Ultra quiet rear exhaust-Open nose design for easy jam clearing-Adjustable depth control for quick countersinking adjustments-Over molded comfort grip-Narrow nose for accurate fastener placement into hard-to-reach areas-Fastener range 1/2 to 1 1/2

Bostitch RHMC13125 2-1/2InchX.131 Round Head Plastic Coallated Metal Connector Nails

-Full Round Head-Bend yield = 100,000 PSI-For Metal Connector Applications-Good for use in all Pressure Treated Lumber

Bostitch RHMC14825 2-1/2InchX.148 Round Head Plastic Coallated Metal Connector Nails

-Full Round Head-Bend yield = 100,000 PSI-For Metal Connector Applications-Good for use in all Pressure Treated Lumber

Max AKHL1050E 400psi High Pressure Air Compressor

Max AKHL1050E is 400 psi High Pressure Air Compressor developed for PowerLite next generation high pressure nailers. It is equipped with DC Brushless Motor which is more powerful, quieter and lighter when compared to the conventional motors. Also the inverter circuit at the motor adjusts the RPM to extract the maximum performance depending on the voltage level. The AKHL1050E also has a 3 fan cooling system which makes a special air flow and minimizes heat build up of the motor. It is also equipped with a safety relief valve which works when air pressure exceeds 435 psi and the 1200h motor was durable enough to withstand lab testing without any maintenance necessary.

Porter-Cable BN18150 18-Gauge 1-1/2 inches Brad Nails

Fits many standard 18 gauge brad nailers 18 gauge for fine finish work Galvanized for corrosion resistance

Porter-Cable BN18075 18-Gauge 3/4 inches Brad Nails

Fits many standard 18 gauge brad nailers 18 gauge for fine finish work Galvanized for corrosion resistance

Porter-Cable BN18175 18-Gauge 1-3/4 inches Brad Nails

Fits many standard 18 gauge brad nailers 18 gauge for fine finish work Galvanized for corrosion resistance

Porter-Cable BN18063 5/8 inch 18 Gauge Brad Nails (5000 per Box)

The Porter-Cable BN18063 is a box of 5000 5/8 inch 18 Gauge Brad Nails. It fits many standard 18 gauge brad nailers. It features 18 gauge for fine finish work and galvanized for corrosion resistance.

Porter-Cable CFNBNS Factory Reconditioned Three Nailer/Compressor Combo Kit

The Porter-Cable CFNBNS is a Factory Reconditioned Combo Kit, which includes a Finish Nailer, Brad Nailer, Stapler, and Compressor.The 150-PSI Porter-Cable compressor with two couplers works on standard household current. Besides driving a large quantity of nails in a single tank charge, the 6-gallon compressor proves useful for other pneumatic tools as well. The two quick connect couplers allow two nail guns to powered at the same time. Besides being quick on recovery, it is also oil-free and maintenance free. This portable compressor weighs just 34 pounds and has a handle on top for easily moving it around.The hardened driver blade ensures maximum durability and reliability for the Porter-Cable nailer. The special design of the tool-free jam release affords a clear line of sight and cuts down on interruptions. The nailers depth of drive can be easily adjusted and the nose tip does not mar the work surface. Die-cast aluminum used in the construct of the body makes the nailer lightweight for extended hours of use and yet strong enough to withstand the harsh jobsite treatment. The Porter-Cable stapler is sturdy and responsive, and does well for upholstery and other furniture coverings etc.

Grip 12673 Goodyear 50-Foot x 3/8-Inch Air Hose

The Grip 12673 is a Goodyear 50-Foot Air Hose. The hose is ideal for use with an air compressor. It is designed to help power all types of pneumatic tools including staple guns, brad nailers, spray guns, air ratchets and more. The rubber hose is weather, oil and solvent resistant.

DeWalt DC612KAR Factory Reconditioned DC612KA XRP 12V/14.4V 16 Gauge Straight Finish Nailer Kit

The DeWalt DC612KA Factory Reconditioned Cordless Finish Nailer powered by DeWalt XRP battery system cycles fast and drives nails in fully without leaving a surface blemish. The XRP batteries are designed to perform 40% more than standard batteries, and provide extended run-time and also ensure a long work life. DeWalt offers the finish nailer in both straight and 20 angled magazine configurations, which accept most brands of 16 gauge straight nails and ensures consistent nail penetration into both soft and hard joints. Portable and versatile, the is ideal for nailing, installing molding, chair rails, cabinetry and other fine finish applications. The finish Nailers top cap is impact resistant and is easily removable for troubleshooting.. The headlights help while working in dimly lit conditions. The numbered, 6-position dial helps in easy referencing of depth levels. The DeWalt DC612KA Finish Nailers nosepiece is designed to for the removal of jammed nailers, without the need to use tools.

Porter Cable C2550 4 Gallon, 150 PSI Portable Air Compressor

-2.5 HP (peak), 1.3 HP (running) 4 gallon, mobile, contractor, pancake style tank air compressor-Two-pole, 3450 RPM capacitor start induction motor for maximum air delivery-Heavy duty, cast iron cylinder construction and large 8 oz. oil capacity to assure long life-High-flo air regulator and push-to-connect coupler-12 Amp current required - Low 12 Amp motor draw prevents accidental tripping of circuit breaker-Cushioned handle for improved comfort and grip. -Frame provides increased mobility; two pick-up points and protection for pump and motor.-4 gallon storage capacity air tank supports heavy usage of brad nailers, staplers, and finish nailers; moderate usage of roofing and framing nailers-CUL listed with ASME safety valve to meet all codes-Air delivery 5.4 SCFM @ 40 PSI, 4.4 SCFM @ 90 PSI83 dBA - quiet operation, Higher 120 PSI cut-in pressure provides 30 PSI of bonus air before a 90 PSI rated air tool becomes inoperable

Spring Tools 32R42-1 Combination 2/32-Inch Nail Starter and 2/32-Inch Nail Set

Spring Tools 32R42-1 is a Combination 2/32-Inch Nail Starter and 2/32-Inch Nail Set. The 2/32-Inch nail set tip sets finish nails in trim and other wood surfaces. Nail setting is ideal in repairing brads from pneumatic nailers that missfire and don't go all the way into the wood surface. Drive nails into any wood surface without a hammer. Perfect for tight spots and for driving small finish nails without hitting fingers with a hammer

DeWalt DCA16200 2-Inch 2500 Count Angle Nails

The DeWalt DCA16200 is a box of 2500 16 Gauge 20 2 Angle Nails. These 16 gauge 20 angled finish nails are manufactured out of cold-worked carbon steel and galvanized in a hot-dip process, which ensures that each nail will resist rust and moisture. These nails are ideal for finish work and are for use with DeWalt cordless angled nailers.

Spring Tools CA198 3 Piece Basic Woodworking Set

Spring Tools CA198 3 Piece Basic Woodworking Set. Nail set is ideal in repairing brads from pneumatic nailers that missfire and don't go all the way into the wood surface. Drive nails into any wood surface without a hammer. Perfect for tight spots and for driving small finish nails without hitting fingers with a hammer. It contains Center Punch & 2/32-Inch Nail Set, 2/32-Inch Nail Starter & 2/32-Inch Nail Set, 5/16-Inch Square Chisel, Hard Storage Case.

DeWalt DCA16250 2-1/2 inch 2500 Count Angle Nails

The DeWalt DCA16250 is a box of 2500 16 Gauge 20 2-1/2 inch Angle Nails. These 16 gauge 20 angled finish nails are manufactured out of cold-worked carbon steel and galvanized in a hot-dip process, which ensures that each nail will resist rust and moisture. These nails are ideal for finish work and are for use with DeWalt cordless angled nailers.

DeWalt DCA16150 1-1/2Inch 2500 Count Angle Nails

The DeWalt DCA16150 is a box of 2500 16 Gauge 20 1-1/2 2500 Count Angle Nails. These 16 gauge 20 finish nails are manufactured out of cold-worked carbon steel and galvanized in a hot-dip process which ensures that each nail will resist rust and moisture. These 1-1/2 16 gauge 20 nails are ideal for finish work and are compatible with DeWalt cordless angled nailers.

Bessey BCS-1 Bessey Reco Induction Bearing Heater 1Inch X 1Inch X 18-3/4Inch Cross Bar for BC Special

-Bessey Reco Induction Bearing Heater 1 X 1 X 18-3/4 Cross Bar for BC Special

Spring Tools WWA1105 Deluxe 5 PC Woodmaster Set

Spring Tools WWA1105 is a Deluxe 5 Piece Woodmaster Set. Nail setters are ideal in repairing brads from pneumatic nailers that missfire and don't go all the way into the wood surface. This set contains a Center Punch & 1/32-Inch Nail Set, 2/32-Inch Nail Starter & 2/32-Inch Nail Set, Self Centering Brad Setter, Self Centering Center Punch, 5/16-Inch Wood Chisel and Combination 2/32-Inch & 3/32-Inch Nail Set. It is perfect for fine woodworking projects and professional trim work.

DeWalt D51257K 16 Gauge 1-1/4 Inch - 2-1/2 Inch Finish Nailer Kit

The DeWalt D51257K is a 16 Gauge 1-1/4 Inch - 2-1/2 Inch Finish Nailer Kit. The D51257K ushers in the next generation of DEWALT finish nailers. Making use of Sealed Lube Dual Technology, allows the unit's motor to work as either an oil free or an oil lubricated unit. Tool-free features include: an adjustable belt hook, nail depth adjustment, jam clearing, and a 360 rotating exhaust cap. Uses 1-Inch to 2-1/2 Inch (25.4 mm - 65 mm) 16 gauge straight collated nails and includes carrying case, 1000 of 2-Inch finish nails, a low profile no-mar pad, a pre-installed sequential action trigger, as well a trigger lock off.

DeWalt D51276K 15 Gauge 1-1/4 Inch to 2-1/2 Inch Angled Finish Nailer Kit

The DeWalt D51276K is a 15 Gauge 1-1/4 Inch to 2-1/2 Inch Angled Finish Nailer Kit. The D51257K ushers in the next generation of DeWalt finish nailers. Making use of Sealed Lube Dual Technology, allows the unit's motor to work as either an oil free or an oil lubricated unit. Tool-free features include: an adjustable belt hook, nail depth adjustment, jam clearing, and a 360 rotating exhaust cap. Uses 1-Inch to 2-1/2 Inch 34 collated 15 gauge nails, and includes carrying case, 1000 2-Inch finish nails, a low profile no-mar pad, a pre-installed sequential action trigger, as well a trigger lock off.

DeWalt D51822R Factory Reconditioned D51822 Heavy-Duty 31° Clipped Head Framing Nailer

The DeWalt D51822 is a Factory Reconditioned Heavy-Duty 31 Clipped Head Framing Nailer. It has 7.5 lbs magnesium housing and aluminum magazine which result in one of the lightest nailers in the industry. Its 12-3/4 Inch height allows for toe-nailing in confined areas. The unique engine design generates power to bury nails in both standard framing lumber and engineered lumber with minimal recoil. Dry fire lockout extends bumper life by preventing tool from actuating when magazine is empty. The impact resistant exhaust deflector protects tool from damage to the cap.

Bessey BCS 3Inch Bessey Reco Induction Bearing Heater 3Inch X 3Inch X 18-3/4Inch Cross Bar for BC Special

-Bessey Reco Induction Bearing Heater 3 X 3 X 18-3/4 Cross Bar for BC Special

Bessey BCS 1-1/4Inch Bessey Reco Induction Bearing Heater 1-1/4Inch X 1-1/4Inch X 18-3/4Inch Cross Bar for BC Special

-Bessey Reco Induction Bearing Heater 1-1/4 X 1-1/4 X 18-3/4 Cross Bar for BC Special

Bessey BCS 2Inch Bessey Reco Induction Bearing Heater 2Inch X 2Inch X 18-3/4Inch Cross Bar for BC Special

-Bessey Reco Induction Bearing Heater 2 X 2 X 18-3/4 Cross Bar for BC Special

Bessey BCRB Bessey Reco Induction Bearing Heater Raising Blocks for BC/BC Special (pair)

-Bessey Reco+D20 Induction Bearing Heater Raising Blocks for BC/BC Special (pair) Raising Blocks (sold in pairs) lift bearing heater crossbar for use with larger diameter bearings.

Festool 489457 48 Tooth Special Circular Saw Blade for TS/ATF 55

ToolKing.com promotional discount codes or coupons are NOT valid on Festool productsThe Festool 489457 is a 48 Tooth Special Circular Saw Blade for portable plunge-cut saws. It is specially designed for laminated floors and polymer materials. With trapezoidal teeth the edges of the teeth are beveled on both sides. The combination of the two different saw teeth cut alternately. This tooth shape is used to cut aluminum, hard plastics and hard coated materials.

Senco Cordless Finish 32 16 Guage Cordless Finish & Trim Nailer

The Senco CORDLESS32 Cordless Finish 32 battery powered finish nailer drives 3/4-Inch to 2-1/2 Inch 16 gauge straight finish nails. Includes two year manufacturers warranty. Comes complete with rugged carrying case, two batteries, and one hour quick charger. No hoses or compressors required. This Cordless Finish 32 is perfect for all your finishing needs. Features include a dual drive control for sequential or contact operation, adjustable depth of drive, molded hand grip, and EZ-Clear Latch to quickly clear jams. Senco cordless nailers drive up 4 nails a second and 1000 nails per charge. Senco Cordless Finish 32 is great for a wide varity of finish and trim appliacatons, furniture and cabinet frames, molding, baseboard, window casing, and upholstery trim panels.

Porter-Cable DA250C 15 Gauge 2-1/2 Inch Angle Finish Nailer

The Porter-Cable DA250C is a 15 Gauge 2-1/2 Inch Angle Finish Nailer. Featuring a long life maintenance/oil-free motor that prevents oil from staining the work surface, an internal piston catch for consistent max power on every shot, and a rear exhaust that keep contaminates away from work, the DA250C is part of the newest generation of Porter Cable finish nailers. With the ability to drive 15 gauge nails from 1" to 2 1/2" in length, a tool-free depth-of-drive adjustment with detents for proper setting of nail heads, tool-free jam release mechanism for easy nail removal, a sequential style trigger with lock off switch and a removable non-marring nose tip with on tool storage, the DA250C meets all of the requirements that the discerning end user demands.

Paslode 500910 T250A-F16 16-Gauge Pneumatic Angled Finish Nailer

The Paslode 500910 T250A-F16 Pneumatic Angled Finish Nailer will quickly become the workhorse of your workshop. It is powerful, yet amazingly lightweight at only 3.8 lbs., and is well-balanced for easy handling, especially when working overhead. Its compact, angled design lets you get into tight spaces that straight nailers cannot. The Paslode T250A-F16 is adjustable to your needs and all of your controls are within reach so you can get through any job quickly. The depth of drive is adjustable without tools, so you can change it with one hand for precise control on hard or soft woods. It has all of the features you want in a finish nailer, thats why it was rated #1 by the Journal of Light Construction.Attention International Customers Paslode products cannot be shipped outside of the USA.

Makita By Amana 733328-A 1/2-Inch Handrail/Table Edge Router Bit

The Makita 733328-A are special router bits used for cutting table top edges or used with handrail side profile bits.

Stanley 55-033 10-Inch Nail Claw

The Stanley 55033 is 10 Nail Claw. It has 10" heat treated bevel nail slot special extracting claw nail claw pry bar. Forged octagon steel, heat treated and toughened to withstand bending and breaking.

Max KH100FT 100 Ft High Pressure Hose

Max KH100FT is a PowerLite 400PSI 100 Feet High Pressure Air Hose. Includes special high pressure quick connect fittings. Maximum pressure of 428 psi (30bar).

Gorilla 6205001 Wood Glue 18 oz Bottle

Gorilla Wood Glue, bonds stronger, faster for wood-to-wood applications. Its hard working and long lasting. The special formula was created for a variety of wood surfaces, is water-resistant, and has no dyes for a better looking bond line.

Couldn't find Special Deals on Bostitch Nailershere? Are you looking for something else? Search our partner sites:

                              Special Deals on Bostitch Nailers