AKEDA                                                                                                                                                                                                  

AKEDA tools and information

Find AKEDA at best prices and buy!

Akeda 3100 Dust Collector Kit

Akeda 3100 is a Dust Collector Kit. The dust collector kit fits Akeda models DC16 and BC24. It's a breeze to install. It snaps into place in seconds and hooks directly to your dust collection hose.

Akeda 3401 Clamp Knob

The Akeda 3401 Clamp Knob is a replacement knob for the Akeda BC and DC model dovetail jigs. The jig has THREE independent parallel clamping systems: the HORIZONTAL clamp, used with half blind pins, the FRONT vertical clamp, used with half blind dovetails, and the REAR vertical clamp, used with through dovetail pins.Recommendations for use of Akeda Clamp Knob:Avoid over clamping and never leave the clamping system under pressure. It is not necessary to apply more than 4 or 5 ft. lbs. of torque to clamp a work piece. Using the AKEDA knob, the average person can generate 4 to 6 ft. lbs. with one hand, and 6 to 8 ft. lbs. with two hands. Applying 8 ft. lbs. of torque will damage a softwood work piece. Try clamping a waste piece progressively tighter until it wont move, and remember the amount of torque to apply next time. Never use a wrench in place of the clamp knob. Damage will result if the torque exceeds 16 ft. lbs. Remove the clamp knob before routing

Akeda 3240 Universal Tail Guides

Akeda 3240 is a set ofUniversal Tail Guides. The package contains 5 Akeda universal tail guides. Theyre included with both Akeda jigs, and are used to form through dovetail tails, half blind dovetail tails, and box joints. When installing guide fingers for the first time, they may be a little stiff. They are deliberately made slightly oversize so they shave down to size.

Akeda 3522 0.434-Inch Precision Undersized Guide Bushing

Akeda 3522 is a 0.434-Inch Undersized Guide Bushing. The high precision thin-wall Akeda guide bushings are accurate to within 0.001. They replace the oversize and undersize router bits. This is a better idea from Akeda, and allows greater adjustment for fit.

Akeda 3521 0.442-Inch Precision Oversized Guide Bushing

Akeda 3521 is a 0.442-Inch Oversized Guide Bushing. The high precision thin-wall Akeda guide bushings are accurate to within 0.001. They replace the oversize and undersize router bits. This is a better idea from Akeda, and allows greater adjustment for fit.

Akeda 3520 0.438-Inch Precision Standard Guide Bushing

Akeda 3520 is a 0.438-Inch Standard Guide Bushing. It is the Standard high precision thin-wall guide bushing from Akeda. It has the correct inside diameter and barrel length for their jigs. Do not use other guide bushings - they are not accurate enough.

AKEDA 3300 64-Piece Universal C-Kit

The AKEDA 3300 Universal C-Kit includes all of the accessories to allow you to form the full range of 7, 9, 11, 14 and 20 through dovetails, all five sizes of half blind dovetails, and box joints with your AKEDA Dovetail Jig. The C-Kit works on both the DC16 and BC24 Dovetail Jig. The kit also includes the dust collection system for connection to your shop vac for a cleaner, safer work environment. This kit is a great deal if youre looking to accomplish a lot on your AKEDA Dovetail Jig; all of these accessories are valued at over 350 when purchased separately.

Akeda 3216 16-Inch Drawer Construction Window

Akeda 3216 is a 16-Inch Drawer Construction Window. The Package has one replacement high impact Lexan window for Akedas model DC16 jig. It snaps into place without special tools. Remove the protective film before installing.

Akeda 3447 1/2-Inch to 8.0mm Collet Reducer

Akeda 3447 is 1/2-Inch to 8.0mm Collet Reducer. Akedas new 8mm shank bits replace their previous 1/4-Inch shank bits. Theyre stronger and you will experience less vibration. You may need this 1/2-Inch to 8mm collet reducer in order to use the Akeda dovetail and/or straight bits if your router does not have an 8mm collet.

Akeda 3230 Half Blind Pin Guides

Akeda 3230 is a set of Half Blind Pin Guides. The package includes five pin guides used to form half blind dovetails and box joints. When installing guide fingers for the first time, they may be a little stiff. They are deliberately made slightly oversize so they shave down to size.

Akeda 3224 24-Inch Blanket Chest BC24 Window

Akeda 3224 is a 24-Inch Blanket Chest Jig Window. The package has one replacement high impact Lexan window for Akedas model BC24 Jig. It snaps into place without special tools. Remove the protective film from both sides before installing.

Akeda 3424 24-Inch Ribbed Rear Guide Rail

Akeda 3424 is a 24-Inch Blanket Chest Rear Guide Rail. The package has one replacement ribbed 9/16-Inch thick rear guide rail for Akedas Model BC24 Blanket Chest Jig. To replace your guide rail, remove the two mounting screws, remove the damaged guide rail, and then install the replacement. Always tighten the left hand guide rail screw first.

Akeda 3820 20 Degree Dovetail Cutter Router Bit

Akeda 3820 is a 20 Degree Dovetail Cutter Router Bit. This Akeda 20 x 1/4-Inch deep dovetail bit with 8mm shank is used with the 20 pin guides to form through dovetails in 1/4-Inch thick material. It is also used to form fixed depth (1/4-Inch) half blind dovetails using the guide fingers included with the jig. This bit has an 8mm shank, so you may need a 1/2-Inch to 8mm collet reducer for your router.

Akeda 3814 14 Degree Dovetail Cutter Router Bit

Akeda 3814 is a 14 Degree Dovetail Cutter Router Bit. This Akeda 14 x 3/8-Inch deep dovetail bit with 8mm shank is used with the 14 pin guides to form through dovetails from 3/8-Inch down to 1/4-Inch thick. It is also used to form fixed depth (3/8-Inch) half blind dovetails using the guide fingers included with the jig. This bit has an 8mm shank, so you may need a 1/20-Inch to 8mm collet reducer for your router.

Akeda 3807 7 Degree Dovetail Cutter Router Bit

Akeda 3807 is a 7 Degree Dovetail Cutter Router Bit. This Akeda 7 x 3/4-Inch deep dovetail bit with 8mm shank is used with the 7 pin guides to form through dovetails from 3/4-Inch down to 1/4-Inch thick. It is also used to form fixed depth (3/4-Inch) half blind dovetails using the guide fingers included with the jig. This bit has an 8mm shank, so you may need a 1/2-Inch to 8mm collet reducer for your router.

Akeda 3811 11 Degree Dovetail Cutter Router Bit

Akeda 3811 is 11 Degree Dovetail Cutter Router Bit. This Akeda 11 x 1/2-Inch deep dovetail bit with 8mm shank is used with the 11 pin guides to form through dovetails from 1/2-Inch down to 1/4-Inch thick. It is also used to form fixed depth (1/2-Inch) half blind dovetails using the guide fingers included with the jig. This bit has an 8mm shank, so you may need a 1/2-Inch to 8mm collet reducer for your router.

Akeda 3880 0.315-Inch Standard Straight Cutter Router Bit

Akeda 3880 is 0.315-Inch Standard Straight Cutter Router Bit. This Akeda 0 .315-Inch (8.0mm) diameter x 1-Inch (25mm) long straight bit with 8mm shank is used to form all through dovetail pin pieces of any size or angle. This bit has an 8mm shank, so you may need a 1/2-Inch to 8mm collet reducer for your router.

Akeda 3858 0.350-Inch Box Joint Cutter Router Bit

Akeda 3858 is a 0.350-Inch Box Joint Cutter Router Bit. This Akeda 0.350-Inch (8.9mm) diameter x 1-Inch (25mm) long box joint bit with 8mm shank is used to form variable 3/8-Inch - 5/8-Inch box joints with the half blind guide fingers included with the jig. This bit has an 8mm shank, so you may need a 1/2-Inch to 8mm collet reducer for your router.

Akeda 3809 9 Degree Dovetail Cutter Router Bit

Akeda 3809 is a 9 Degree Dovetail Cutter Router Bit. This Akeda 9 x 5/8-Inch deep dovetail bit with 8mm shank is used with the 9 pin guides to form through dovetails from 5/8-Inch down to 1/4-Inch thick. It is also used to form fixed depth (5/8-Inch) half blind dovetails using the guide fingers included with the jig. This bit has an 8mm shank, so you may need a 1/2-Inch to 8mm collet reducer for your router.

Akeda 1600 DC16 Drawer Construction Jig with 64-Piece Universal C-Kit

Akeda dovetail jigs are the only jigs to let you adjust your through dovetail pin angle according to your stock thickness. This means you can get stronger dovetails, even on thinner stock. That's something professional craftsmen and novices, alike, can appreciate. The DC16 Drawer Construction Dovetail Jig is built for the toughest applications. With 28 pounds of steel and aluminum, this jig dampens vibration for easier use and is sturdy enough to never wimp out on you. You can get more elegant results with the Akeda DC16, too. Akeda dovetail bits are .445-Inch diameter. That means you can create slightly more slender and more traditional pins than with the common 1/2-Inch dovetail jigs. Also, the Akedas guide fingers sit below the surface of the guide rail, so your router base never touches them. Those subtle difference are what really makes the difference in the Akeda dovetail jigs.In this package with the dovetail jig comes the AKEDA Universal C-Kit, which includes all of the accessories to allow you to form the full range of 7, 9, 11, 14 and 20 through dovetails, all five sizes of half blind dovetails, and box joints with your AKEDA Dovetail Jig. The C-Kit works on both the DC16 and BC24 (sold separately) Dovetail Jigs. The kit also includes the dust collection system for connection to your shop vac for a cleaner, safer work environment. This kit is a great deal if you're looking to accomplish a lot on your AKEDA Dovetail Jig; all of these accessories are valued at over 350.00 when purchased separately.

Akeda 3800 Dovetail Router Bit Set - 7 Piece

Akeda 3800 is 7-piece Dovetail Bit Set. The Bit Set consists of a plastic storage case containing all five dovetail bits, the .315-Inch Straight Bit, and the .350-Inch Box Joint Bit. All router bits are 8mm shank.

Akeda 3450 BC/DC Dovetail Jig User Manual

The Akeda 3450 is a User Manual for the BC/DC Dovetail Jigs. This 49-page manual is used with Akedas DC16 Drawer Construction Jig and BC24 Blanket Chest jig. Its concise, well illustrated, and easy to follow. It contains many hints and tips and a trouble-shooting section. It folds open flat on your bench for easy reference.

Akeda 3211 11 Degree Through Dovetails Pin Guides

Akeda 3211 is a set of 11 Degree Through Dovetail Pin Guides. The package includes five 11 pin guides used to form through dovetails in material from 1/2-Inch down to 1/4-Inch thick with the matching angle 11 bit. The 11 angle is better suited to material 1/2-Inch thick. It is stronger than the 9 angle, and forms a more slender, aesthetically-pleasing pin profile. When installing guide fingers for the first time, they may be a little stiff. They are deliberately made slightly oversize so they shave down to size.

Akeda 3207 7 Degree Through Dovetail Pin Guides

Akeda 3207 is a set of 7 Degree Through Dovetail Pin Guides. The package includes five 7 pin guides used to form through dovetails in material from 3/4 down to 1/4 thick with the matching angle 7 bit. The 7 angle is the only choice for material 3/4 thick. When installing guide fingers for the first time, they may be a little stiff. They are deliberately made slightly oversize so they shave down to size.

Akeda 3214 14 Degree Through Dovetails Pin Guides

Akeda 3214 is a set of 14 Degree Through Dovetail Pin Guides. The package has five 14 pin guides used to form through dovetails in material from 3/8-Inch down to 1/4-Inch thick with the matching angle 14 bit. The 14 angle is better suited to material 3/8-Inch thick. It is stronger than the 11 angle, and forms a more slender, aesthetically-pleasing pin profile. When installing guide fingers for the first time, they may be a little stiff. They are deliberately made slightly oversize so they shave down to size.

Akeda 3220 20 Degree Through Dovetails Pin Guides

Akeda 3220 is a set of 20 Degree Through Dovetail Pin Guides. The package has five 20 pin guides used to form through dovetails in 1/4-Inch thick material with the matching angle 20 bit. The 20 angle is better suited to material 1/4-Inch thick. Its stronger than the 14 angle, and forms a more slender,aesthetically-pleasing pin profile. When installing guide fingers for the first time, they may be a little stiff. They are deliberately made slightly oversize so they shave down to size.

Akeda 3417 16-Inch Ribbed Drawer Construction DC16 Rear Guide Rail

Akeda 3417 is a 16-Inch Drawer Construction Rear Guide Rail. The package has one replacement ribbed 9/16-Inch thick rear guide rail for Akedas Model DC16 Drawer Construction Jig. To replace your guide rail, remove the two mounting screws, remove the damaged guide rail, and then install the replacement. Always tighten the left hand guide rail screw first.

Akeda 3209 9 Degree Through Dovetails Pin Guides

Akeda 3209 is a set of 9 Degree Through Dovetail Pin Guides. The package has five 9 pin guides used to form through dovetails in material from 5/8-Inch down to 1/4-Inch thick with the matching angle 9 bit. The 9 angle is better suited to material 5/8-Inch thick. It is stronger than the 7 angle, and forms a more slender, aesthetically-pleasing pin profile. When installing guide fingers for the first time, they may be a little stiff. They are deliberately made slightly oversize so they shave down to size.

AKEDA Robot Clasificador de Basura

Couldn't find AKEDAhere? Are you looking for something else? Search our partner sites:

                                                        AKEDA